BLSD-HV Series Brushless DC Motor Drive

High voltage, AC/DC dual-purpose, wide voltage range, variable parameter settings, 2 quadrant

 Brief Introduction:

  • Surface mounted technology to improve the reliability of the circuit.
  • PLC interface, high voltage and wide voltage range.
  • 0-10V analog voltage / pulse width signal / pulse frequency signal supports. 
  • Optoelectronic isolation for all the ports with over temperature, over current, short circuit, under voltage, over voltage and other protections. 
  • Military conformal coating for PCB surface, moisture, mold, dust-proof. 
  • Super safe and super reliable.

Definition of Part number:

BLSD
220
16
ADC
2Q
HV
T
BLDC drive
Rated Voltage
Peak current limit
AC/DC input ①
Control mode
Parameter ②
Temp ③

① :  This code shows the DC Power input type of the drive: ADC=AC and DC dual purpose; DC = Normal DC input; LDC = Ultra low voltage DC input; WDC = Wide range DC input; AC = AC input.
② : This code shows the parameter type of the drive: S = Simple fixed parameter; N = Variable parameter; H = High current; SH = Small type high voltage; HV = High voltage. 
③ : This code shows the temperature range of the drive: T = -40 ~ +65 ℃ , None = -10 ~ +45℃ .
Note: In order to let the part number easier to read, Some part number code will not be shown in the specification table, a code “X” will be instead. The full part number will be provided in the quotation or the proforma invoice..

Specifications:

Model

 

Temp
range
(ºC)
Voltage
range
(VDC/VAC)
Peak Current adjustable
(A)
Continuous
Current
adjustable
(A)
60º/120º
Hall
sensor
PWM f(kHz)PI
Close
loop
of speed
or current
RC
Ramp
time
(S)
Reference
Input Range
LV/OV
Alarm
Alarm
diag
output
PG speed
pulse output
Current/ speed loop switchSetting
by
switch
and potentio-meter
SC/ OTSafe F/RSafe Start
BLSD11008ADC-2Q-HV-X-10~+45
or
-40~+65

AC 110
(AC 45-140)orDC 155

(DC 60-195)

4~82~4

 

16

 

 

 

0-10V
or
PWM
or
0-3KHz pulse customizable

 

 

4p@8-pole
or
24p@8-pole
BLSD11016ADC-2Q-HV-X8~164~816
BLSD11024ADC-2Q-HV-X12~246~1216
BLSD22008ADC-2Q-HV-X

AC 220
(AC 45-275)orDC 310

(DC 60-385)

4~82~416
BLSD22016ADC-2Q-HV-X8~164~816
BLSD22024ADC-2Q-HV-X12~246~1216

All the drivers in the above table can use AC and also DC input. When use AC, the driving voltage mode in the motor port is DC, the voltage is 1.4 times than input AC voltage. When use DC, the driving voltage mode in the motor port is DC, the voltage is same with input DC voltage

Technical Note:

1. Power Supply Port:

A wide range AC or DC power supply of AC45-275V/50-60Hz in single phase, DC60-385V can be used for the driver. The PE point of driver and power supply system must be connected reliably for safety. Please take attention to the high voltage warning.

2. Motor Windings Port:

Connect three phases of windings to the U/V/W points in correct sequence. PE on motor case must be connected to PE point of this port for safety. Please take attention to the high voltage warning.

3. Motor Hall Sensor Port:

Connect Hall sensors Hu/Hv/Hw to the port in correct sequence. This port is insulated from inside circuit by optocoupler and Vc supply is provided by driver.

       

4. Control Signal Port:

This port is insulated from inside circuit by optocoupler and one line isolated 12V power supply is provided by driver for external use, the current is less than 50mA

  • F/R: Rotating direction control. Forward=open ,Reverse=connect to SGND

  • The driver can provide safety forward/reverse control. If the direction is changed suddenly when the motor is running, the motor will cut down the power and sliding to zero speed smoothly and then change rotating direction in order to avoid the shock impact. At the moment that the driver power up, if the speed is not zero, then it will start until the speed is zero.

  • EN: Enable control function. Enable when optocoupler conduct. The driver can only be work when enable. The alarm can be reset by EN=disable once

  • SV:Analog reference voltage input of 0~10V. Input impedance 200K. It is insulated from inside circuit by a linear optocoupler.

  • SVP:Digital reference pulse input of 0~3KHz frequency or 0~100% PWM@50-1KHz .

  • PG:Speed pulse output in OC(30Vmax/5mA). This signal can be made in synchronize to one phase hall sensor signal or 6 times frequency multiplier. The motor speed is in proportion to the frequency. Motor speed(rpm)=PG frequency(Hz)x120/N. N is the pole number of motor. Or, motor speed(rpm)=PG frequency(Hz)x120/N/6 (6 times frequency multiplier).

  • AL:Alarm output in OC(30Vmax/5mA). The driver has self-diagnostic function. When the following conditions come, the alarm comes up, and optocoupler will conduct.

            For items of NO.1~5, green LED P/A will be blinking. The alarm can be reset by EN=disable once.
            For items of NO.6~7, red LED will brighten. The alarm can be reset only you Off-on supply again.

            1. Incorrect Hall signal    2. Low control voltage    3. OT at main chip    4. LV or OV at power supply voltage    5. current continuous overload (Peak current limiting) over 6 seconds     6. Case temperature over     7. Short circuit in motor windings. 

Vc,SGND: One line isolated 12V power supply is provided by driver for external use, the current is less than 50mA

5. LED Display:

  • HV: DC bus voltage instruction LED. Green color LED. High voltage on DC power line when brighten. Warning: Do not open the case and touch the high voltage parts when this LED brightens. 

  • P/A: Green color LED. Control supply and Alarm. LED will be blinking in alarm state.

  • SHAFT: Green color LED. When motor shaft is moving, LED will brighten, When moving stopped, LED turns dark. In order to avoid the danger, do not touch the shaft and the related components when this LED brightens.

  • SC: Short circuit indicator LED. Red color LED. When Short circuit in windings of motor, LED will brighten. The alarm can be reset only you Off-on supply again after removal of fault.

  • OT: Over temperature indicator LED. Red color LED. When over temperature at driver case,  LED will be brighten and alarm. The alarm can be reset only you Off-on supply again after apply the cooling measures.

6. Potentiometers:

R-PC:Peak current ratio,50%-100%    R-LG:Loop gain,2-22    R-RT:Ramp time,0.2-2.2S    R-SV:Reference ratio,0-100%. Usually used for precisely calibrating in full speed control instructions. Also can be used for internal speed control potentiometer by its attenuation effect.

7. Switches:

SW1-1:ON=120°Hall sensors,OFF=60°Hall sensors

SW1-2:ON=Close loop,OFF=Open loop

SW1-3/4:ON/OFF=Speed loop,OFF/ON=Current loop

SW1-5/6:ON=Increase loop filter time,OFF=Decrease loop filter time

SW1-7/8/9/10:Max speed range setting. It’s related to the motor poles, please check the table printed in the driver case.

SW2-1/2/3:ON/OFF/OFF=0-10V analog input at SV,OFF/ON/OFF=0~100% PWM (1~2KHz) input at SVP,OFF/OFF/ON=0~3KHz pulse frequency input at SVP.

SW2-4:ON=PG frequency is 6x Hall sensor frequency per phase

               OFF=PG frequency is 1x Hall sensor frequency per phase

       

Customization:

heatsink.jpgmotor.jpglogo.jpg
 Heat sinkMotor tuningLogo / brandmark
  1. Heat Sink: Heat sink can be added according to customer request.
  2. Motor Tuning: Drivers can be tuned to fit the motors with different poles to match customer’s applications. 
  3. Logo and brandmark: Customer’s Logo/brandmark can be printed on the frame of the driver according to the customer’s request.
Scroll to Top
Scroll to Top